Favor

Talk about 20 28 gauge & .410 bore shotguns here.
Post Reply
ShortMagFan
Posts: 45
Joined: May 15th, 2021, 8:22 pm

Favor

Post by ShortMagFan »

Need a picture of your 301 .410 choke, out of the barrel, next to a measuring tape. Thanks in advance

Trying to figure out the threads on a choke I have
User avatar
redarrow
Gobbler Nation
Gobbler Nation
Posts: 5856
Joined: October 2nd, 2011, 9:26 am
Location: S E Michigan

Re: Favor

Post by redarrow »

It might be more helpful for you to post a pic of your choke tube .These fellas are pretty good at determining what you have just by looking.
Put you plans in the nail scarred hands.
southpaw
Posts: 129
Joined: March 22nd, 2017, 8:46 pm

Re: Favor

Post by southpaw »

Not sure if this gonna work. It is 1/4" from the bottom to the start of the threads. It is 7/8" to the top of the threads. 1.5" to where it touches the top of the barrel.
Attachments
301410new.png
ShortMagFan
Posts: 45
Joined: May 15th, 2021, 8:22 pm

Re: Favor

Post by ShortMagFan »

Thanks Southpaw. That’s perfect and exactly what I needed
SteveRoseRAS
Posts: 30
Joined: July 31st, 2021, 6:36 pm
Location: Pembroke, KY
Contact:

Re: Favor

Post by SteveRoseRAS »

The 301 should use what Carlson refers to as "Short Invector", the tube is 1.5" inside the barrel. As far as I know that 1.5” long choke is specific to the 301

https://www.choketube.com/interchange- ... -shotguns/

https://www.choketube.com/product-categ ... 1-5-flush/

The standard flush fit "Invector" tube is 1.9" long (the section that is inside the barrel)
Steve Rose
Rose Action Sports, LLC
Pembroke, KY
ShortMagFan
Posts: 45
Joined: May 15th, 2021, 8:22 pm

Re: Favor

Post by ShortMagFan »

SteveRoseRAS wrote: September 13th, 2022, 3:04 pm The 301 should use what Carlson refers to as "Short Invector", the tube is 1.5" inside the barrel. As far as I know that 1.5” long choke is specific to the 301

https://www.choketube.com/interchange- ... -shotguns/

https://www.choketube.com/product-categ ... 1-5-flush/

The standard flush fit "Invector" tube is 1.9" long (the section that is inside the barrel)
Yes this is consistent with what I found in my research last night and the picture confirms what I have is a 301 “short invector” choke.

Appreciate the help
User avatar
Hoobilly
Gobbler Nation
Gobbler Nation
Posts: 13330
Joined: August 15th, 2011, 10:15 pm
Location: Argos Indiana
Contact:

Re: Favor

Post by Hoobilly »

SteveRoseRAS wrote: September 13th, 2022, 3:04 pm The 301 should use what Carlson refers to as "Short Invector", the tube is 1.5" inside the barrel. As far as I know that 1.5” long choke is specific to the 301

https://www.choketube.com/interchange- ... -shotguns/

https://www.choketube.com/product-categ ... 1-5-flush/

The standard flush fit "Invector" tube is 1.9" long (the section that is inside the barrel)
Yep you got it
Same thread pattern it’s just a shorter choke
Don't start none, won't be none!

https://foxtrotammo.com/
Post Reply

Return to “Small Bore”