Need help with roll crimper for 410
Need help with roll crimper for 410
Can someone tell me what is the best roll crimper for 410? I have the BPI and it works, but the crimps look terrible, shoot good, but look terrible!
Send me a link to the best one and that’s where I will look! I’ve looked at the GAEP, but there is to many different options. I get confused!
Thanks in advance.
Send me a link to the best one and that’s where I will look! I’ve looked at the GAEP, but there is to many different options. I get confused!
Thanks in advance.
Re: Need help with roll crimper for 410
BPI always makes ugly crimps.
I have the gaep and a Precission Reloading tool and the best crimps come if I use the gaep first and then hit them again with the PR. Little time consuming but turns out the best that way. Neither one by itself looks as good.
I have the gaep and a Precission Reloading tool and the best crimps come if I use the gaep first and then hit them again with the PR. Little time consuming but turns out the best that way. Neither one by itself looks as good.
Re: Need help with roll crimper for 410
Can you give me specifics as to what crimps you are using? Links to purchase would be awesome!
- hookedspur
- Gobbler Nation
- Posts: 2371
- Joined: May 24th, 2012, 8:44 pm
- Location: Ohio
Re: Need help with roll crimper for 410
Dale Wildman for the GAEP
Re: Need help with roll crimper for 410
Nick Ross roll crimper is the easiest one to use and produces real nice crimps. Gaep is good also but for reloading hulls the Gaep crimps a real tight fold over that makes reloading a hull a pain.
https://www.thereloadersnetwork.com/pro ... 410-gauge/
https://www.thereloadersnetwork.com/pro ... 410-gauge/
Wasn't born, I was hatched!!!!!!!!!!!! and raised in Tennessee.
- Turkinator
- Gobbler Nation
- Posts: 3006
- Joined: May 13th, 2013, 6:25 pm
- Location: southern onio
Re: Need help with roll crimper for 410
If you can find one a Lyman makes the best I’ve tried. Another option would be an antique roll crimp tool
Re: Need help with roll crimper for 410
I second the recommendatio from the reloader's network. A buddy uses one for 10 gauge and it makes a great crimp. It's a 4 pin head. I don't know about the .410 but I've seen the one my buddy has and its well made and solid. I second the use of a vintage hand cranker. Only new ones I've had were from siarm, but hard to get without European connections. Gil
https://www.thereloadersnetwork.com/?s= ... ping+tools
https://www.thereloadersnetwork.com/?s= ... ping+tools
- DocHolliday
- Posts: 519
- Joined: April 18th, 2012, 1:46 pm
- Location: Louisiana
Re: Need help with roll crimper for 410
I put this in the copy of this thread yesterday,
NRA Benefactor Life Member
Re: Need help with roll crimper for 410
I loaded up 3 for tomorrow checking zero and first day in the woods. Note the crimper. It is clamped to the end of a board. With my knee pressed against the board pushing it into the coffee table, with my left hand clamping the board and the rto's lever to raise the shell against the crimper, I hand cranked with the right hand with the results depicted. This is why Doc, me and others prefer the vintage rto's. No electric drill or drill press required to make great crimps. Note sleeping bird dog, my 8 year old Brittany, asleep on the couch. Gil
Last edited by GLS on March 23rd, 2023, 5:48 pm, edited 1 time in total.
- DocHolliday
- Posts: 519
- Joined: April 18th, 2012, 1:46 pm
- Location: Louisiana
Re: Need help with roll crimper for 410
Love’em! You done good. Unfortunately, hen’s teeth are like oak leaves on the ground in fall compared to an antique .410 rto tool. I’m glad I got one-such pretty crimps!
NRA Benefactor Life Member
- Turkinator
- Gobbler Nation
- Posts: 3006
- Joined: May 13th, 2013, 6:25 pm
- Location: southern onio
Re: Need help with roll crimper for 410
I have seen very few 410 antique tools. Thankfully I have found a few 20s
- DocHolliday
- Posts: 519
- Joined: April 18th, 2012, 1:46 pm
- Location: Louisiana
Re: Need help with roll crimper for 410
Thanks toGil’s information, I found one in France. Love not money would cause me to part with it.
NRA Benefactor Life Member
-
- Posts: 27
- Joined: March 18th, 2019, 2:45 am
Re: Need help with roll crimper for 410
I have the gaep and the one from reloader network and I like them both about the same.
Re: Need help with roll crimper for 410
I ordered the Reloaders network roll crimper! Hopefully that helps me out.
- DocHolliday
- Posts: 519
- Joined: April 18th, 2012, 1:46 pm
- Location: Louisiana
Re: Need help with roll crimper for 410
Let us know how the .410 turns out,
NRA Benefactor Life Member
Re: Need help with roll crimper for 410
If anyone comes across another one of the antique RTO units for the 410, please let me know! I would love to have one!!
Re: Need help with roll crimper for 410
Well, here I am still waiting for a tracking umber from reloaders network! Ordered on the 22nd and have not heard a word from them! Are they trustworthy business? I am about to open a dispute thru PayPal! I emailed them, but no response!
- DocHolliday
- Posts: 519
- Joined: April 18th, 2012, 1:46 pm
- Location: Louisiana
Re: Need help with roll crimper for 410
I got a couple last fall. It did take a while. It’s almost like they are made t order. Took almost 3 weeks iirc.
NRA Benefactor Life Member