Annihilator broadheads

A general discussion area for turkey hunters.
Post Reply
User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 9089
Joined: August 15th, 2011, 10:15 pm
Location: Argos Indiana

Annihilator broadheads

Post by hoobilly » October 15th, 2020, 5:45 pm

Anyone on here use these on deer or turkeys yet?

“Ego is the anesthesia to dull the pain of stupidity”
Spoken by someone smarter than I

jsh909
Posts: 585
Joined: May 11th, 2019, 7:12 am
Location: Ohio

Re: Annihilator broadheads

Post by jsh909 » October 18th, 2020, 6:18 am

I could not get them to tune in my bow. I wanted to like them. They would "knuckle ball" every time and didn't group well. I tried them with Easton Axis with blazer and heat vanes with same results. I also tried them with XX75 with three inch straight vanes then I built 3 XX75 2315s with a couple degree right offset 3inch vane to try to stabilize them. Grouping was better but still couldn't get them in tune. I really wanted to like them. I have had to build arrows for other heads too, so it's not a quality issue. My setup just didn't like them, your results may vary. They seem very well built, needed touched up to get a razor edge, they are quiet in flight.

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 9089
Joined: August 15th, 2011, 10:15 pm
Location: Argos Indiana

Re: Annihilator broadheads

Post by hoobilly » October 20th, 2020, 9:34 am

jsh909 wrote:
October 18th, 2020, 6:18 am
I could not get them to tune in my bow. I wanted to like them. They would "knuckle ball" every time and didn't group well. I tried them with Easton Axis with blazer and heat vanes with same results. I also tried them with XX75 with three inch straight vanes then I built 3 XX75 2315s with a couple degree right offset 3inch vane to try to stabilize them. Grouping was better but still couldn't get them in tune. I really wanted to like them. I have had to build arrows for other heads too, so it's not a quality issue. My setup just didn't like them, your results may vary. They seem very well built, needed touched up to get a razor edge, they are quiet in flight.
I wonder how they would work on a longer bolt crossbow

Like that they are quiet in flight
“Ego is the anesthesia to dull the pain of stupidity”
Spoken by someone smarter than I

jsh909
Posts: 585
Joined: May 11th, 2019, 7:12 am
Location: Ohio

Re: Annihilator broadheads

Post by jsh909 » October 20th, 2020, 4:59 pm

hoobilly wrote:
October 20th, 2020, 9:34 am
jsh909 wrote:
October 18th, 2020, 6:18 am
I could not get them to tune in my bow. I wanted to like them. They would "knuckle ball" every time and didn't group well. I tried them with Easton Axis with blazer and heat vanes with same results. I also tried them with XX75 with three inch straight vanes then I built 3 XX75 2315s with a couple degree right offset 3inch vane to try to stabilize them. Grouping was better but still couldn't get them in tune. I really wanted to like them. I have had to build arrows for other heads too, so it's not a quality issue. My setup just didn't like them, your results may vary. They seem very well built, needed touched up to get a razor edge, they are quiet in flight.
I wonder how they would work on a longer bolt crossbow

Like that they are quiet in flight
I would say they are worth a shot

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 9089
Joined: August 15th, 2011, 10:15 pm
Location: Argos Indiana

Re: Annihilator broadheads

Post by hoobilly » October 20th, 2020, 10:30 pm

jsh909 wrote:
October 20th, 2020, 4:59 pm
hoobilly wrote:
October 20th, 2020, 9:34 am
jsh909 wrote:
October 18th, 2020, 6:18 am
I could not get them to tune in my bow. I wanted to like them. They would "knuckle ball" every time and didn't group well. I tried them with Easton Axis with blazer and heat vanes with same results. I also tried them with XX75 with three inch straight vanes then I built 3 XX75 2315s with a couple degree right offset 3inch vane to try to stabilize them. Grouping was better but still couldn't get them in tune. I really wanted to like them. I have had to build arrows for other heads too, so it's not a quality issue. My setup just didn't like them, your results may vary. They seem very well built, needed touched up to get a razor edge, they are quiet in flight.
I wonder how they would work on a longer bolt crossbow

Like that they are quiet in flight
I would say they are worth a shot
I should buy them and try..
“Ego is the anesthesia to dull the pain of stupidity”
Spoken by someone smarter than I

jsh909
Posts: 585
Joined: May 11th, 2019, 7:12 am
Location: Ohio

Re: Annihilator broadheads

Post by jsh909 » October 21st, 2020, 6:29 pm

Hey it's just money!

User avatar
hoobilly
Gobbler Nation
Gobbler Nation
Posts: 9089
Joined: August 15th, 2011, 10:15 pm
Location: Argos Indiana

Re: Annihilator broadheads

Post by hoobilly » October 22nd, 2020, 7:32 am

jsh909 wrote:
October 21st, 2020, 6:29 pm
Hey it's just money!
Grows on trees? 😂
“Ego is the anesthesia to dull the pain of stupidity”
Spoken by someone smarter than I

jsh909
Posts: 585
Joined: May 11th, 2019, 7:12 am
Location: Ohio

Re: Annihilator broadheads

Post by jsh909 » October 22nd, 2020, 11:46 am

hoobilly wrote:
October 22nd, 2020, 7:32 am
jsh909 wrote:
October 21st, 2020, 6:29 pm
Hey it's just money!
Grows on trees? 😂
I bet they would be lethal if they tune for you

spider316
Posts: 510
Joined: March 24th, 2017, 9:44 am

Re: Annihilator broadheads

Post by spider316 » October 22nd, 2020, 3:37 pm

hoobilly wrote:
October 22nd, 2020, 7:32 am
jsh909 wrote:
October 21st, 2020, 6:29 pm
Hey it's just money!
Grows on trees? 😂
So doesn't moss and mushrooms, no wonder TSS cost so much ! :bootyshake:

Post Reply

Return to “Gobbler Talk”

Who is online

Users browsing this forum: No registered users and 117 guests